Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
Have you been searching for answers on Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is additionally a reasonably tough job. If the old bathtub is conveniently accessible, the project can relocate quickly; if you have to open a wall surface to eliminate the old tub and also place the new tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the work as well as fit trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to think about utilizing one before you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly help you set up a brand-new tub in your restroom if you have actually currently gotten a new bathtub as well as do not need to change the arrangement of your previous water supply pipes.
Your devices and also product list need to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, switch on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be rather problematic as a result of the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and also check all joints as well as new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow outlet and also the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bath tub has actually been used a minimum of once as this will certainly settle it right into its last setting.
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealant can split fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a good friend on a different web address. Sharing is good. You won't know, you might be helping someone out. Thanks for your time. Come back soon.
Automated Marketing Report this page